Polyurethane Foam Foundation Crack Repair Kit 30 ft. w/ Epoxy Paste Surface Sealer

Polyurethane Foam Foundation Crack Repair Kit 30 ft. w/ Epoxy Paste Surface Sealer
ITEM #: CR301302KT30
Brand: Concrete Sealers USA
Availability: In Stock
Lead time: Typically Leaves Warehouse in 1-2 Business Days
Shipping: $20.00 (Fixed Shipping Cost)
STANDARD SHIPPING METHOD: Ground Delivery (3 - 5 Business Days)
Concrete Crack Repair
Foundation Crack Repair
Polyurethane Foam + Epoxy Paste
# of components
2 Part System
carrier type
Solvent Based
voc content
Amber + Gray

Product Description
The Polyurethane Foam Foundation Crack Repair Kit 30 ft. w/ Epoxy Paste Surface Sealer is intended for repairing typical, non-structural wall cracks in poured foundations. The kit includes our CR301 Injection Foam, CR302 Epoxy Paste, and all necessary components to repair up to approximately 30 feet of cracks.

The CR301 Injection Foam is a hydrophobic polyurethane liquid which is designed to stop water infiltration or exfiltration. When the Injection Foam meets water, it reacts with it and then repels any excess water forming a closed cell foam barrier which will not allow water to pass through it. It adheres tenaciously to practically all substrates, wet or dry. Its low viscosity makes it ideal even for repairing hairline cracks. It sets rapidly and expands up to 20 times its original volume to ensure even large cracks or voids are repaired. When cured, it maintains its cured volume with minimal shrinkage and its flexible nature allows it to expand and contract with foundation movement. The CR301 Injection Foam is designed to be used when greater than 20% movement (expansion and contraction) of the substrate is anticipated or where an epoxy repair product is not considered necessary.

The CR302 is a high modulus thixotropic epoxy paste designed to seal cracks and adhere surface ports prior to the injection of our CR301 Injection Foam crack repair product. CR302 will cure in the presence of moisture although application onto wet surfaces is not recommended. It is ideal for do-it-yourselfers and inexperienced applicators or contractors due to its extended working time of 6-7 minutes. Allows for injection within 2-3 hours.

Includes the necessary materials to repair up to approximately 30 feet of cracks up to 3/8" wide:

  • 3 dual cartridges of CR301 Injection Foam
  • 3 dual cartridges of CR302 Epoxy Paste Surface Sealer
  • 6 cartridge cross-over restrictors
  • 1 syringe blow hole repair material
  • 4 1/4" x 24" mixing tubes and 4 retaining nuts
  • 50 surface ports and caps
  • 10 corner ports
  • 4 hose assemblies
  • 1 trowel and 1 wire brush
  • 5 pair of nitrile gloves
  • 1 pair of safety glasses
  • 1 reusable tool box
  • 1 dual manual dispensing gun
  • Technical Data Sheet & SDS
  • Written instructions

Recommended Uses
The CR301 Injection Foam is typically used to stop water leaks coming through cracked or honeycombed concrete, voids between walls and floors, walls and ceilings, expansion joints, cold joints and pipe intrusions. It is used to repair concrete walls, ceilings and floors that are leaking. It is not intended for repairing structural cracks in foundations. The CR302 is recommended for use in sealing foundation wall cracks and adhering surface ports prior to the injection of our CR301 Injection Foam crack repair product.

Surface Preparation & Application
Surface must be dry and free of any dirt, dust, or debris prior to application to ensure a superior bond. For some surfaces, it may be necessary to give the surface a profile prior to applying. This can be done by lightly sanding the surface or by profiling with a wire brush. CR302 remains on the surface after application but may be removed with a chisel, sander, or grinder.

Refer to the Technical Data Sheet for instructions prior to use.


Consult Safety Data Sheet prior to use. Wear glasses and gloves. Avoid contact with skin and eyes. 
EYES: Flush with large amounts of water, minimum of 15 minutes.
SKIN: Wash thoroughly with soap and water. Remove contaminated clothing.
INHALATION: Leave area for fresh air. If not breathing, give artificial respiration and call physician.
INGESTION: Do not induce vomiting. Seek medical care immediately.
The Manufacturer warrants products to be free from defects in material or manufacturing. Products are further warranted for adequacy of design when used in accordance with design limits, and properly specified and installed. This warrant does not apply to uses not in compliance with specific applications and installation procedures. All warranty obligations of the manufacturer shall be limited, at the discretion of the manufacturer, to repair or replacement of the defective product. These remedies shall constitute the manufacturer’s sole obligation and sole remedy of purchaser under this warranty. In no event will the manufacturer be responsible for incidental, consequential, or specific loss or damage however caused.

Typically Leaves Warehouse in 1-2 Business Days and Arrives via Ground Delivery 

Ground Delivery 
This item is delivered via Standard Ground Delivery service via UPS or Fed Ex and generally arrives within 3-5 business days of leaving the warehouse. At this time, we do not offer any premium or express delivery options (ex. Next Day Air).

Prior to use, we would recommend consulting the product label, product technical data sheet, and SDS sheet. For your benefit, this information is included below.

PDF Icon CR301302KT30 Product Label

PDF Icon CR301302KT30 Technical Data Sheet

PDF Icon CR301302KT30 SDS Sheet


The following coverage rates are approximate and for estimating purposes only and are for 1 application. We would recommend making test applications on actual surfaces to determine exact coverage rates.

Sign up for our newsletter